Quick Specs

Digital Production Switchers - Synergy 100 MD

Physical Characteristics

Control Panel Connector Types
To rack frame:		8 pin shielded Telco
Tally 1 & 2:		12 pin detachable terminal block
DC Power:		12VDC, 2 Amp power jack

Power Consumption - Control Panel
Input voltage:		90V~250V AC, 47~63Hz
Control panel:		maximum 27 VA

Power Consumption - Rack Frame
Input voltage:		100V~120V AC, or 220V~240V AC 47~63Hz 9A 650W (Canada 120V ~ only)
Frame (with no options):		~ 150W
Frame (with all options):		~ 500W

Environmental Characteristics

Panel and rack frame separation:		1000 ft (305 m) max
Ambient temperature range:		0 - 40 °C (32 – 104 °F)
The video processing circuitry is cooled by a set of fans using side-to-side airflow. The fans are speed controlled by multiple temperature sensors within the frame
The control panel is convection cooled (no fans) for silent operation.

Video Characteristics

Video Processing
Supported Video Formats
480i/59.94 (SD 525)		SMPTE 125M, SMPTE 259M
576i/50 (SD 625)		ITU-R BT.601-5, SMPTE 259M
720p/59.94		SMPTE 296M, SMPTE 292M
720p/50		SMPTE 296M, SMPTE 292M
1080pSF 24, 1080pSF 23.98		SMPTE RP 211, SMPTE 292M
1080i/50, 1080i/59.94		SMPTE 274M, SMPTE 292M
1080p 24		SMPTE 292M
10 bit 4:2:2 component digital video and key processing
4:3 and anamorphic 16:9 switchable aspect ratio where applicable
Contact Ross Video as additional format compatibility is planned

Video Inputs
Number of inputs:		16
Equalization: (using Belden 1694 cable)		> 75m @ 1.5Gb/s > 150m @ 270Mb/s
Impedance:		75 ohm, terminating
Return loss:		> 20 dB @ 1.5 GHz
All inputs are SMPTE-259M/292M serial digital non-looping.
The Synergy 100 MD comes standard with 16 inputs.
Inputs can be used for either key or video.
The reference input is selectable, analog black for standard Definition operation, and the recommended tri-level sync for High Definition operation.
The reference input is a looping, non-terminated input.

Video Outputs
Number of video outputs:		16
Return loss:		> 18 dB @ 1.5GHz
Rise and fall time:		800 ps +/- 10%(SD) 240 ps +/- 10%(HD)
Signal level:		800 mV +/- 10%
DC offset:		0 volts
Overshoot:		< 8%
All video outputs are 10-bit SMPTE-259M-C (SD Mode) or 10-bit SMPTE-292M serial digital (HD Mode).
EDH is inserted into all MLE outputs and can be disabled. Aux Bus outputs do not have EDH insertion but do pass previously inserted EDH. (SD Video Mode)
Line CRCs are inserted into all MLE outputs and can be disabled. Aux Bus outputs do not have line CRCs inserted but do pass previously inserted line CRCs. (HD Video Mode)

Jitter
HD		Tri-Level Sync - Alignment (> 100KHz) <0.2 UI - Timing (<10Hz) <1.0 UI Performance not guaranteed with composite reference.
SD		Tri-Level Sync - Alignment (> 1KHz) <0.2 UI - Timing (< 10 Hz) <0.2 UI Composite Ref. - Alignment (> 1KHz) <0.2 UI - Timing (< 10 Hz) <0.5 UI

System Timing

All video inputs zero time relative to reference input, auto timing will correct for inputs out of time by up to +/- 0.25 line.

System delay approximately 400 pixels

Note: Specifications are subject to change without notice

Product Navigation